While the iPhone X and newer are waterproof, they are not completely "waterproof". A small drop of water is enough to activate it.iPhone Liquid Contact Indicator (LCI). This indicator is located under the SIM tray. The LCI is usually white or silvery. Turns red in contact with water. You can confirm liquid detection by removing the SIM tray and checking the LCI color. When LCI is activated, iPhone issues a Liquid Detection Alert indicating:Liquid detected not Lightning connectoroStore not available.You see the same error every time you plug in the Lightning cable.

Most of the time, this warning appears with two options:To denyYemergency referral. But sometimes you only see Ignore option. If you select emergency cancel it will still charge but it is dangerous for your iPhone. Ignore the notification and continue with the instructions in this article to clear the water in the charging port.


Contact with water can corrode the Lightning connector (charging connector). It is never the "water" that damages the port, but the salts in the water. These salts or impurities will cause the water to conduct electricity and this will damage your phone. This error is recoverable if only water enters the charging port, not the circuit board. In the latter case, the chances of your iPhone surviving are slim.
Possible causes of liquid detection alarm
Let's look at the most likely scenarios for how you caused your Lightning Connector to stop working.
when taking a shower –We don't hesitate to put our iPhones in the sink while showering, as long as they are completely waterproof. We put a few drops of water on the canvas, which we simply wipe off with a towel. However, if a drop of water enters the charging port, the iPhone will sound a water detection alarm.
rain water -If you've been out with your iPhone in your pocket in rainy weather, surely a few drops of water can get into the Lightning port, disabling the port for charging your phone.
Spilled drink/water –Sometimes we spill a drink on our iPhones and hack into the charging port. It is difficult for liquid to penetrate the screen or buttons, as Apple guarantees that its iPhones are highly resistant to water ingress. Still, a few drops might get into the charging port.
body sweat -If you're sure your iPhone hasn't been exposed to water, body sweat could be causing a liquid detection alert. You might be holding your phone with sweaty hands and a drop or two might have fallen into the charging port.
Damaged charging cable -It's not always the port that prevents charging. Sometimes the fault lies with the charging cable. Drops of water can get on the pins of the charging cable, and when you plug in the Lightning connector, you get an error message:„Store not available.”
What not to do when iPhone gives liquid detection alert?
According to Apple support, place your iPhone in arice bowl,drying with afanocompressed air, and define aforeign objecton the Lightning connector, drops of water may press harder. This increases the damage chance. In addition,Heatingfrom an external source can heat up your iPhone, slow your phone down, cause data corruption, and compromise your security with battery leaks.
What to do when iPhone gives water detection alerts
Now that you know what not to do, let's dive into the proper steps to remove water from your charging port.
Step 1Remove the case and turn off your iPhone
As soon as you get your iPhone out of the water,turn it off immediatelyand remove the cover. There may be water under the case, which can get into sensitive components. Also, turn off your iPhone. Using it when wet can cause even more damage.
Step 2: Disconnect all accessories
After turning off the phone, remove all accessories such asCorporal Lightning, living voice,etc you should take yoursim cardMapas well as. Do not reinsert the SIM card or other accessory until it is completely dry. Make sure you turn off your iPhone. If there is water in the charging port or on the circuit board, connecting to a power source can be dangerous.
Step 3: Dry your iPhone
After disconnecting all accessories, wet your iPhone with a towel or tissue. This prevents water from penetrating further into the screen layers, buttons or circuit boards. However, do not put a cloth in the door, as this can be risky.

Step 4 – Gently tap the palm of your hand
Gently tap iPhone in the palm of your hand with the connector facing down to dislodge any water droplets from the Lightning connector. It forces the water to go down and out of the harbor. This strategy, recommended by Apple Support Service, is considered the safest and most efficient.
Step 5: Try a Different Lightning Connector
If the Lightning connector is dry but your iPhone still has the liquid detection error, pay attention to your Lightning cable. There may be a hardware issue. Contact with water can also damage the cable. The drops get under the pins on the charging cable, which is why you get a "Charge Not Available" warning on your iPhone.

Try a different charging cable to find out the real cause of the error. If your iPhone is charging with another cable, then the cable has been damaged. For a better user experience, it is recommended to use genuine Apple accessories.
Step 6: Store in a well-ventilated place for 24 hours
If trying a different cable didn't work, the problem is most likely the Lightning port. Once the iPhone detects liquid in the port, it will continue to display an alert even after the port dries up. The iPhone is very sensitive and does not allow charging for a few hours. It's best to leave the iPhone in a well-ventilated area for a day. You can check in the middle of luck.
Step 7: Restart iPhone
After waiting 24 hours, restart your iPhone. If the same error occurs then restart your phone. A reset will clear minor bugs and restart your phone. Follow the steps below to reset.
- To closepower switchYVolume up/down buttonsimultaneously.
- A slider will appear on the screen, move it toTo switch off.
turn off your iphone
- Waiting30 seconds.
- hold thepower switchuntil the Apple logo appears on the screen.
Use a wireless charger
The Liquid Detection Alarm comes with Emergency Dismiss and Cancel options. You can force your iPhone to charge by choosing the emergency cancel option, but doing so may damage your device. You can buy a wireless charger if no other methods to remove liquid detection popup work. A wireless charger can be safely used in this situation.

Contact Apple Support
If none of the above methods work for you, contacting Apple support is the last option you can try. You can visit your local Apple Store or call support to pick up your iPhone for service.
Above:If you're sure the Lightning connector is completely dry but the pop-up warning is still there, try charging your iPhone before the battery drops below 40%. This trick has helped quite a few people. Try it and see if it works for you.
keep reading
- Replace iPhone 5/5s/5c charging port or dock connector
- How to Connect Xbox One Liquid Metal Controller to PC
- Liquid Nitrogen Pushes Intel's i9-13900K Beyond 8.0GHz
- DEEPCOOL CASTLE 360RGB V2 Liquid CPU Cooler Review
key words
Top-Smartphones
FAQs
How do I get my iPhone to stop saying liquid detected? ›
Tap your iPhone gently against your hand with the Lightning connector facing down to remove excess liquid. Leave your iPhone in a dry area with some airflow. After at least 30 minutes, try charging with a Lightning cable or connecting a Lightning accessory.
Why does my iPhone keep saying liquid detected but not wet? ›If your iPhone and Lightning accessory aren't wet
If you see this alert every time you connect a certain cable or accessory, that cable or accessory might be damaged. Contact the manufacturer. If you see this alert every time you connect an Apple Lightning cable or accessory, contact Apple Support.
But if it's an emergency, you can override the liquid detected in lightning connector message and charge your phone. You can do so by removing the charging cable and then re-inserting it. The same “liquid detection" message will appear, but you'll now have the option to tap Emergency Override and charge your phone.
Why does it say liquid detected when there is no liquid? ›What Does Liquid Detected in Lightning Connector Mean? Apple calls the iPhone's charging port the Lightning Connector. So, when you get a message saying “Liquid Detected in Lightning Connector”, it means that there is water either in your iPhone's charging port or the charging cable is wet.
Is my phone broken if it says liquid detected? ›If you see one of these alerts, your iPhone has detected liquid in the Lightning port or on the Lightning cable or Lightning accessory. To protect your iPhone and the accessory, charging and accessory connection will be unavailable until the Lightning port and accessory have dried.
How long does a lightning connector take to dry? ›It may take several hours for your iPhone's charge to become available again. - Liquid inside the Lightning connector: we recommend disconnecting the cable and even turning off the iPhone to dry it out. It may take several hours... So be patient!
Should I override iPhone liquid detection? ›But there are a few things you shouldn't do when the “Liquid Detected in Lightning Connector” alert appears on your iPhone. For one, you shouldn't click the emergency override button on the alert. You could severely damage your iPhone, causing more problems in the long run.
How long does it take for moisture detected to go away? ›Let the device air dry for at least 24 hours before turning it on again or plugging it into power, or else further damage may occur. If no moisture is seen or suspected: First, plug your phone into the charger, at which point you should still receive the error.
What happens if you override liquid detection? ›The liquid present in the Lightning port could permanently damage your iPhone's hardware. We don't recommend tapping Emergency Override to charge your iPhone.
How do you force stop moisture detected in charging port? ›If moisture is detected in the USB port, an error message will be displayed and charging will stop. In this case, unplug your device from the charger, then wipe with a dry cloth or gently shake your device (5-10 times) with the port facing downwards to release any excess moisture.
How long does it take for charging port to dry? ›
Water will naturally evaporate from the charging port within approximately 1 to 2 hours. If any liquid other than fresh water enters the charging port of your device, you must rinse it in fresh water and dry it thoroughly with a dry, soft cloth.
How do I turn off moisture detection? ›- Clear USB Cache. ...
- Disable Fast Charging. ...
- Charge Your Phone via Computer. ...
- Sign Out and Sign In to Your Samsung Account. ...
- Try Safe Mode. ...
- Use Wireless Charger.
Put Your Phone in Front of a Fan, or Leave it to Dry Naturally. If you want to speed up the drying process of your phone's USB port, we recommend placing it in front of a fan or even near an open window (if you're sure it's not going to rain!).
How do I know if my Lightning port is damaged? ›- Broken Pins in Phone Charger Port. Similarly, if pins inside the port become broken or bent, correct charging will become impossible. ...
- Debris in Phone Charger Port. ...
- Charger Cable and Adapter Work With Other Devices. ...
- Faulty Phone Charger Adapter. ...
- Defective Phone Battery.
To override the liquid detection alert, simply reconnect the Lightning cable or accessory shortly after it appears. When the liquid detection alert pops up again, tap the new Emergency Override button.
What happens if I press emergency override on my iPhone? ›Select Emergency Override
Selecting this option will enable you to charge your iPhone by overriding the automatic charging disablement feature. This option is to be used if it is an emergency and you need to charge your phone. This will start charging but also this may damage your iPhone.
...
How to Remove Water From The Charging Port? Android/iPhone Users
- Remove Moisture. The very first thing that you would do is to try to remove any moisture from the surface of the charging port. ...
- Let it Evaporate. ...
- Use a Wireless Charger. ...
- Contact Customer Service.
Most iPhone and iPod devices are equipped with Liquid Contact Indicators (LCIs) that you can see from the outside. An LCI will activate when it contacts water or a liquid containing water. The indicator's color is normally white or silver, but when it contacts water or a liquid containing water, it will turn fully red.
How do I get rid of liquid app on my iPhone? ›- Install the free Sonic App on your iPhone and launch it.
- Place your iPhone flat or on a slight incline with the lightning port at the bottom.
- Tap the water drop icon in the center of the screen to start the process.
- Let the app run for around 10 seconds and tap STOP.
If solving your moisture problem is something you'd like to do inexpensively, rock salt may be your answer. Because rock salt is hygroscopic it absorbs moisture from the air. If your plan is to get rid of the humidity in a damp basement, start with a 50-pound bag of sodium chloride to make your rock salt dehumidifier.
What can cause false moisture readings? ›
The most common cause is metal hidden in or behind the material being checked. Corner beads, metal studs, foil-backed insulation and metal lath in plaster walls are all common examples. Dense materials such as concrete and plaster also read “wetter” on a non-invasive meter.
Are moisture sensors accurate? ›A high-quality moisture meter used on the right material can be accurate to within less than 0.1% of the material's moisture content by weight. However, a low-end moisture meter can be wildly inaccurate.
Why won't the moisture detected won't go away? ›If your device displays a water drop icon which signifies moisture detection, you should power off your device and leave it to dry completely. If the icon does not go away and you continue to experience issues with charging, try clearing your USB cache.
How do you air dry a charging port? ›Leave your device in a dry area for at least an hour with the charging port facing down. This will allow airflow into the port and force excess water to drip out on its own. If you suspect your USB-C or Lightning cable is also wet, store it in a dry place where air can reach it for an hour as well.
Can I dry my phone with a hair dryer? ›Do not -- we repeat, do not -- use a blow dryer; the heat can damage the phone. If you have a phone or a gadget with a cover that comes off, take it off, and take out the battery, the SIM card, and anything else that can easily be removed. Dry all those things off.
Can water permanently damage charging port? ›Anything that could expose your charge port and therefore the inside of your phone to moisture may damage the wiring. If your phone gets wet, immediately turn it off and get it as dry as possible. The longer it is exposed to water, the more water will leak in through the charge port and headphone jack.
Will it destroy my phone to charge it with a slightly wet charging port? ›If your iPhone has been exposed to liquid, unplug all cables and do not charge your device until it's completely dry. Using accessories or charging when wet may damage your iPhone. Allow at least 5 hours before charging or connecting a Lightning accessory.
How long does it take for moisture to dry in USB port? ›Wait for moisture to evaporate.
Water will naturally evaporate from the charging port within approximately 1 to 2 hours. If any liquid other than fresh water enters the charging port of your device, you must rinse it in fresh water and dry it thoroughly with a dry, soft cloth.
If your iPhone hasn't been exposed to water or liquid, and there isn't any dust in the connector, you can safely tap the emergency override button. As mentioned, this button will both dismiss the alert and allow the phone to resume its normal function.
What happens if you emergency override liquid in charging port? ›Override for Emergency. Because there is moisture or liquid in the iPhone's charging port, you receive this notice when it's plugged in. This notice indicates that charging via the charging port is not possible on your device.
Why does my iPhone 12 keep saying liquid detected? ›
The Liquid Detected message on your iPhone is a warning to avoid potential disaster. There are two options you can select: Dismiss and Emergency Override. If you choose to Dismiss, the warning message will be removed from your screen, and your device won't charge until it's dry.
What app pushes water out of phone? ›Although, newer iPhones and Android devices have waterproof ratings, they have no built-in tool or mechanism to eject water should it get into your phone. Luckily, there's an app (dubbed Sonic) that helps people expel water from their devices. And it's quite fast and easy.
What is iPhone liquid damage? ›Most iPhone and iPod devices are equipped with Liquid Contact Indicators (LCIs) that you can see from the outside. An LCI will activate when it contacts water or a liquid containing water. The indicator's color is normally white or silver, but when it contacts water or a liquid containing water, it will turn fully red.